#QUICK99SI INPA DOWNLOAD 6.4.3 HOW TO#
#QUICK99SI INPA DOWNLOAD 6.4.3 INSTALL#
#QUICK99SI INPA DOWNLOAD 6.4.3 FULL#
#QUICK99SI INPA DOWNLOAD 6.4.3 WINDOWS 10#
#QUICK99SI INPA DOWNLOAD 6.4.3 CODE#

I am stumped as I want to code the car for my brother-in-law. I know my modified cable works fine now that I modified it because Dis 44 and INPA wasn’t communicating before I modified the cable. What needs to be done to make connection with Progman SSS V32? Do I need to change anything in the Ediabas configuration. Progman starts to reads the FA/ZCS after you choose the car model and then after awhile it says it requires an Edic/Icom cable connection. INPA and Dis 44 work perfect but I cant get Progman to work.

I modified my cable with a switch and have 7 and 8 bridged to work with a 2004 E46. Note which postion is on and which is off by some type of label on the outside of the cover…SImple! Note on my first pic, I have a switch with 3 prongs, but I snipped off the 3rd one just to make it easier to solder… Screw in the 4 philip head screws in their respected holes. At the end there will be one prong end not used…Neatly place the wires snug so that the D-can cover can be closed without anything preventing it to make a closed seal and your done. Connect each pin 7 and 8 with a separate wire and then use the soldering gun and connect each wire to the micro on/off switch… If you bought a 2 prong on/off switch connect it to each side, but if you bought a switch with three prongs, connect the middle and one of the ends, doesnt matter which one. Once you locate pin 8, thats the pin we will be using as well as the next one over. One side will have the digit 1 and the other digit 8 Locate pin 8 which will have a number on the side of the board. Drill bit 5/16 to make hole in the D-can cover Small philip screwdriver to take the D-can cover offĢ Radio Shack micro on/off switch (can be two prongs or three) and some wire 24 guage.Ĥ. Its actually very simple that any average person can do that has access to a drill and a soldering gun.ġ. You will need to solder a bit but it’s nothing too serious if you follow the instructions to the letter. Cost for this would probably range anywhere between 10 to 20 bucks.

#QUICK99SI INPA DOWNLOAD 6.4.3 INSTALL#

Build in 2 lines K and D-Can magisterialīMW INPA Ediabas 5.0.2 download, inpa 5.06 download, inpa 6.4.7 download here…and install it on Windows XP/ Vista or Windows 7/ 8/ 10 (32bit or 64bit), to get it work with K+DCAN USB cable.īasically, there are two methods for users to get the INPA K+DCAN usb cable, to buy a complete one or simply build one yourself. Read the following to get it.

#QUICK99SI INPA DOWNLOAD 6.4.3 FULL#

Interface USB OBD2 for BMW – INPA/Ediabas – K+DCAN allows full diagnostic of BMW from 1998 to 2008 (all functions as in OMNITEC interface). Download and Install ODIS 5.BMW INPA K+CAN With FT232RL Chip K DCAN USB Interface.

#QUICK99SI INPA DOWNLOAD 6.4.3 WINDOWS 10#

Steps to install VAS5054A ODIS Windows 10 64bit.

#QUICK99SI INPA DOWNLOAD 6.4.3 HOW TO#

Then, i did the same to the inpa folder and that was a quick fix for the ediabas and inpa….to get started on windows 7 64bit…disv57 and sss progman took me a while longer because they dont tell you how to really do it in the instructions….it took me days but i figured it all out…i just havent got around to NCS expert yet….i know i got it to work with ediabas 7.0….that was ncexpert 4.0.x but inpa 5.0.2 doesnt work with ediabas 7.0….and inpa.7.0.6 is in german….boooo…lol/////however i guess you have to choose….i think sss is more user freindlyįor konw more information about step-by-step insatllation instrution, please go to And when it said this file already exists, i just put copy and replace for everything. So this is what you do.you download BMW standard tools 2.12.īmw tools 2.12 doesn’t include the root folders for inpa or ediabas.so next what you do is download it from kickass.to Link ()download it…make sure you have the main ediabas and inpa folders that you have already downloaded or got from a CD with your cord….and what i did was opened the torrent folder and copied the files from folder 2 over my existing ediabas folder. Quick fix for whomever runs into that problem > it is a very common error especially if you experiment with different versions of these programs NOTE: make sure your ediabas.ini file is set to port 192.186.68.1) INPA K+CAN Full Diagnostic interface for BMW Wth FT232RL Chipįor window 7 64bit, you have to use the Edibas 6.4.7 (latest) and INPA 5.02 setup. Here is the cutomer solution on setup INPA 5.0.2 and Ediabas 6.4.7 on Windows 7 OSīmw Softing Inpa v5.0.2 Ediabas v6.4.7.rar INPA 5.0.2 and Ediabas 6.4.7 is the Engineer Software for E series, for diagnosis, dealing with BMW complex Electronic Control Units (ECU) along the entire process chain requires reliable communication and data description.

Quick99si inpa download 6.4.3